Nor-lake AdvantEDGE Direct Draw Beer Coolers Manuel d'utilisateur télécharger pdf

09/13 Rev. H 143596

DIRECT DRAW BEER COOLERS

Installation, Operation and Maintenance Instructions

INSPECTION

When the equipment is received, all items should be carefully checked against the Bill

of Lading to ensure all crates and cartons have been received. Do not sign the freight

bill clear until the freight has been properly inspected for damage. All units should be

inspected for damage including concealed damage by uncrating immediately. If any

damage is found, it should be reported to the carrier at once, noted on the Bill of Lading

and a claim should be filed with the carrier. This equipment has been inspected and

tested in the manufacturing facility and has been crated in accordance with

transportation rules and guidelines. The manufacturer is not responsible for freight loss

or damages.

INSTALLATION

After removing the unit from the packaging, clean the interior and exterior surfaces of

the unit with soap and water and a rinse with clean water. Do not use chlorinated

cleaners on the surfaces as they can cause corrosion.

This unit is designed for indoor use only. Be sure to locate the unit where the floor can

support the weight of the unit and product installed inside of it. The refrigeration system

located at the bottom left of the unit requires free air access for proper operation. Allow

a minimum of two inches between the back of the cabinet and the wall. Do not locate

the unit next to heat generating equipment or in direct sunlight.

Confirm that the proposed electrical outlet has the correct voltage, frequency and

current carrying capacity for the requirements of the unit. This information is noted on

the data plate on the inside left wall of the unit. The unit should be isolated on a circuit.

Do not use an extension cord to get power to the unit. Improper electrical installations

will void the compressor warranty. To prevent shock and fire, be sure the unit is properly

grounded.

Local health codes may require that the unit be sealed to the floor with an NSF

approved silicone sealant if it is not on legs or casters. After the unit is set in its desired

location, simply apply a bead of sealant around the base of the unit and smooth it out.

The drain pan under the beer spigots requires a floor drain (except model DD24). The

drain line comes out the back of the unit and is terminated with a ½” barbed fitting. The

installer will need to add a drain line from this fitting to a floor drain. Model DD24 has an

internal drain bottle that captures the beer from the drain pan. This bottle needs to be

monitored and emptied as needed.

1 2 3 4 5 6

Résumé du contenu

Page 1 - DIRECT DRAW BEER COOLERS

09/13 Rev. H 143596 1 DIRECT DRAW BEER COOLERS Installation, Operation and Maintenance Instructions INSPECTION When the equipment is received, al

Page 2 - OPERATION AND MAINTENANCE

09/13 Rev. H 143596 2 It is recommended that the beer delivery system be installed by your local beer distributor. Inside the unit (except on mode

Page 3 - TROUBLESHOOTING

09/13 Rev. H 143596 3 Condenser Coil Prior to cleaning the condenser coil disconnect the unit from power. Periodic cleaning of the condenser coil w

Page 4 - 09/13 Rev. H 143596

09/13 Rev. H 143596 4 DD SERIES REPLACEMENT PARTS LIST Item Number Part Number Description DD24 DD59 DD69 DD79 DD95150229 X150315 X X X X150204 X15

Page 5 - DD24 PARTS DETAIL

09/13 Rev. H 143596 5 DD24 PARTS DETAIL DD59, DD69, DD79 AND DD95 PARTS DETAIL

Page 6

09/13 Rev. H 143596 6

Commentaires sur ces manuels

Pas de commentaire

Nor-lake AdvantEDGE Direct Draw Beer Coolers Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Réfrigérateurs Nor-lake AdvantEDGE Direct Draw Beer Coolers. Nor-Lake AdvantEDGE Direct Draw Beer Coolers User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Réfrigérateurs Nor-lake AdvantEDGE Direct Draw Beer Coolers